Ten short steps. Set it up now
Contractor guide

OSHA Silica Rule: What Small Countertop and Tile Crews Actually Have to Do

If your crew cuts, grinds, or drills stone countertops or tile, you are covered by OSHA's respirable crystalline silica standard for construction, 29 CFR 1926.1153. The permissible exposure limit is 50 micrograms per cubic meter over an eight hour shift. There is no small employer exemption from the rule itself.

By Joe Petocz, EstimateElite. Updated .

Does this rule apply to my remodeling crew?

Yes. The construction silica standard covers all occupational exposures to respirable crystalline silica in construction work. The permissible exposure limit is 50 micrograms per cubic meter as an eight hour time weighted average 1. If your crew cuts, grinds, polishes, or drills materials that contain crystalline silica on a job site, you are covered.

Respirable crystalline silica exposure can lead to silicosis, lung cancer, chronic obstructive pulmonary disease, and kidney disease 2. The dust is released when workers cut, grind, or finish materials with high silica content 3. This is not an abstract risk. OSHA launched a focused inspection initiative in 2023 specifically targeting engineered stone fabrication and installation 4.

Countertop materials vary widely in silica content. Countertops may contain more than 90 percent silica 3. Granite contains up to 50 percent silica 3. Some products made from recycled glass and Portland cement contain less than 0.2 percent crystalline silica 3. The higher the silica content, the more dangerous the dust, and the stricter your controls need to be.

What does the standard require?

The core of the standard is a permissible exposure limit of 50 micrograms per cubic meter of air, measured as an eight hour time weighted average. There is also an action level of 25 micrograms per cubic meter, which is half the permissible exposure limit 1. Once your workers are at or above the action level, additional requirements kick in.

For construction employers, OSHA provides two paths to compliance. The first is Table 1, which lists 18 common construction tasks with specified dust controls, work practices, and respiratory protection 1. If you fully implement the controls for your task, you do not need to measure exposure. The second path is to conduct your own exposure assessment through air monitoring, then implement controls to stay below the permissible exposure limit.

Either way, every employer whose workers engage in tasks involving silica exposure must have a written exposure control plan 1. This plan must include task descriptions, control methods, housekeeping measures, and procedures to restrict access to work areas where workers might be exposed above the permissible exposure limit.

Table 1 tasks most relevant to remodeling crews
TaskRequired controlsRespirator needed?
Cutting with a handheld power sawUse saw with integrated water delivery to suppress dustNo, if water used continuously
Cutting with a stationary masonry sawUse saw with integrated water deliveryNo, if water used continuously
Grinding with a handheld grinderUse grinder with shroud and dust collection systemYes, when used indoors or in enclosed areas
Drilling with a handheld drillUse drill with dust collection system or wet methodNo, if controls used properly
These are simplified summaries. See the full Table 1 in 29 CFR 1926.1153 for all conditions and footnotes.

What are the medical and training requirements?

If any worker is required to use a respirator for silica work for 30 or more days per year, the employer must offer medical surveillance 1. That means an initial exam within 30 days of assignment, then every three years after. The exam must include a chest X ray and lung function test.

Every worker who is or may be exposed at or above the action level must be trained on the health hazards of silica, the specific tasks that could create exposure, the controls being used, the purpose and proper use of respirators, and the medical surveillance program.

You must also keep accurate records of exposure assessments, medical surveillance, and your written exposure control plan. These are not optional for small crews. If OSHA inspects and you have no records, that is a separate citable violation.

EstimateElite shows you every homeowner's budget before you pick up the phone. See how the setup works

What happens if OSHA inspects and you are not compliant?

OSHA is actively looking at this. In 2023, the agency launched a Respirable Crystalline Silica Focused Inspection Initiative targeting engineered stone fabrication and installation industries 4.

Here is what a real citation looks like. Brazilian Stone Design LLC, a Georgia countertop manufacturer, was cited for seven serious violations and hit with $33,000 in penalties 2. The company failed to require respirator use, did not conduct fit testing or provide training for workers using respirators, and neglected to carry out necessary air monitoring 2.

Each violation is cited separately. Each missing piece of documentation, each untrained worker, each day without required controls can be its own line item. For a small company, one inspection with multiple violations adds up fast. OSHA also adjusts penalties upward for willful or repeated violations, which carry much steeper fines than a first time serious citation.

What about California?

California is going further than federal OSHA. Cal/OSHA is moving toward an emergency regulation that would prohibit employers from manufacturing or fabricating artificial stone containing more than 1% crystalline silica by weight 5. That would effectively ban fabrication of most engineered stone countertops in the state.

If you do countertop work in California, you need to follow Cal/OSHA rules in addition to the federal standard. The proposed regulation would also require that for high exposure trigger tasks, employers generally would have to provide full face, tight fitting powered air purifying respirators or other respirators providing an assigned protection factor of at least 1,000 5. That is a much higher level of respiratory protection than the federal standard typically requires.

What can a small crew do right now?

You do not need to hire a consultant to start. These steps cover the basics.

  • Use wet methods for every cut. A continuous water feed on your saw or grinder is the single most effective control and it is specifically what Table 1 calls for.
  • Never dry cut or dry grind stone or tile indoors. If you must work dry, use a tool with a shroud and HEPA filtered dust collection and add a respirator.
  • Write your exposure control plan. It does not need to be long. List the tasks your crew performs that create silica dust, the controls you use for each, and who is responsible for making sure they happen.
  • Get your crew trained. Every worker who handles silica generating tasks needs to know what the dust does to lungs, what controls are in place, and how to use their respirators.
  • If any worker is required to wear a respirator for silica work for 30 or more days per year, schedule their medical exam.
  • Keep records. Document your exposure controls, training dates, and medical surveillance. If OSHA shows up, records are the first thing they ask for.
  • Consider material choices. Products with little or no crystalline silica content can eliminate or reduce the hazard entirely 3. Choosing lower silica materials means less exposure, fewer controls, and less risk.

How to use OSHA's free help

OSHA runs a free On Site Consultation Program specifically for small businesses. It is completely separate from enforcement. A consultant will walk your shop or job site, identify hazards, and help you build a compliant silica program. They will not fine you or report you. This program exists because OSHA knows small employers often want to comply but do not know where to start.

You can request a consultation through your state's program. Find it at osha.gov or call 1 800 321 6742. If you are running a small crew and are not sure whether your controls are good enough, this is the lowest risk way to find out.

Know what materials your homeowners are asking about before you show up

EstimateElite asks homeowners about their project scope and material preferences so you know which jobs involve silica generating work before you schedule a visit.

Questions

Common questions.

Yes. Cutting, grinding, or drilling ceramic tile, porcelain tile, or natural stone tile releases respirable crystalline silica dust. If your crew does this work, the standard applies. Use wet cutting methods and you will likely stay compliant through Table 1.

Sources

Where EstimateElite fits

  • AI assistant

    Ask it in plain words. It builds estimates and takeoffs from plans or photos, writes scopes and change orders, makes pictures, drafts your texts and emails, and moves your leads and calendar for you.

  • Pipeline and inbox

    Drag a lead across your stages, open it to see the price they saw and the finish they picked, and reply from the same screen. Your close rate, pipeline value and won value sit at the top.

  • EstimateElite vs JobTread

    JobTread runs budgets and projects. EstimateElite runs everything before the contract.

  • Estimating software for remodelers, compared

    What each kind of tool does, the products remodelers compare, and where each one stops.

Keep reading